Scoring

Scoring cricket

Ball by ball — runs, extras and wickets in one tap each, with who's batting and bowling set once at the top.

Cricket divisions score ball by ball: one tap per delivery, with the striker, non-striker and bowler held at the top of the pad so you never re-enter them. Overs and wickets build the score; the format you picked for the division decides the rest — T20, One-day, The Hundred (five-ball overs) or Test (two innings a side, with declarations and the follow-on).

Who's in

Above the run buttons sit three chips: striker, non-striker and bowler. Set them once at the start of the over and every ball you tap carries them automatically. Tap a chip to change it — at the end of an over the pad asks for the next bowler, and the strike swaps itself on odd runs.

The bowler chip only offers your fielding side, and anyone who cannot legally bowl the next over is shown greyed out with the reason next to their name — whether they bowled the previous over, or have already bowled their maximum. You are told before you tap, rather than after.

A ball at a time

Tap the runs scored: 0 through 6. Wide and the other extras — no-ball, bye, leg-bye, penalty — sit alongside, and each one records as that ball with the extra attached rather than as a separate entry.

Every tap answers in plain words along the bottom of the pad — FOUR · Kannan · through covers — with Undo beside it. Tap the confirmation and you can add detail to what you just recorded, like the type of shot. Nothing is asked of you that the ball itself already knows.

Wickets

Wicket asks only what changes. Pick how the batter went — bowled, caught, LBW, run out, stumped and the rest — and the pad asks who was out only when that isn't obvious, and for the fielder only when the dismissal involves one. Credit to the bowler follows from the dismissal, so it is never a question.

After a wicket the pad prompts for the incoming batter. Retire handles a batter leaving without being dismissed: it offers only the two batters currently at the crease, then asks why — hurt, out, or another reason. The incoming batter follows your batting order.

Undo

Straight after a tap, while the entry is still held, Undo removes it outright — it never reaches the record, so there's nothing to explain later. After that it is a correction on an append-only ledger: the entry is undone rather than erased, and the scorecard can always be reconstructed.

The rest of the innings

If a side has used up its reviews for the innings, that side is greyed out when you record the next one, with the reason shown — an umpire review is never limited. Toss, reviews, innings close and — in Test formats — declarations, the follow-on and the close of the match are all on the pad. The commonest sit as their own buttons; the rest are under More actions, which always offers exactly what the format and the current state of the match allow.

Super overs

A tied match goes to a super over automatically when your division has it enabled — there's no separate "start super over" step. It's scored with the same run, extra and wicket tiles as the rest of the innings.

The side that batted second in the match bats first in the super over, so whoever bowled second in the match bowls first here. Two wickets ends that side's over (a super over is all out much sooner than a full innings), and so does bowling out the over. The reply then chases whatever the first side scored, plus one — reach that and the match is over on the spot.

Still level after that? Your division's still-tied rule decides what happens next: repeat plays another super over, and keeps going until someone wins; boundary count gives the match to whoever hit more boundaries across the whole match, main innings included; shared records the match as a tie outright.

Recording level

Ball by ball is the finest level a cricket match records, and it is available on every plan — a cricket pad opens there. Drop to a lower level on the Recording chip and the pad records innings totals instead: a correct score and correct standings, with fewer details behind them. The chip always says which level you're on, in words. See choosing a detail level.

Over-by-over or ball-by-ball

Every innings decides its own level from your first entry, not from a setting you pick beforehand. Tap a run, an extra or Wicket first, and that innings is scored ball by ball from then on. Tap End of over first instead, and it records over by over: each entry opens showing the innings' running total, ready to edit up to what actually happened, so you never add up an over yourself. Once an innings has picked a level the buttons for the other one drop away, since they'd no longer agree with the score.

Tapped the wrong one? Undo the very first entry for that innings and it goes back to undecided, exactly as if nothing had been recorded — tap again to lock in whichever level you meant.

Common questions

Does The Hundred's five-ball over work? Yes — the over fills to whatever the format sets, not always six.

Can someone score from the boundary? Yes, with a device link. It scores the same way and can't finalize the match.

Signal dropped mid-over? Entries queue on the device and send when it returns — see scoring without signal.